Narishige Pc10 Manual New Exclusive [90% FREE]

: Set the heater block according to the glass capillary diameter.

Understanding the physical layout is key to navigating the manual 1.2.1.

: If the slider falls prematurely in two-stage mode, check the First Pull Terminating Position Adjusting Slider and ensure the solenoid coil is functioning. narishige pc10 manual new

For users seeking the "new" experience, the PC-100 represents the modern iteration of the instrument. Here's a quick comparison of their key differences:

: Ensure you're working with the most current version of the Narishige PC-10 manual to benefit from the latest information and recommendations. : Set the heater block according to the

A heavier weight (using 4x weights instead of 2x) results in a shorter, wider pull.

The original PC-10 uses mains voltage inside the case. A modernized manual should include warnings about capacitor discharge and heater element replacement frequency. For users seeking the "new" experience, the PC-100

| Problem | Probable Cause(s) | Remedy(ies) | | :--- | :--- | :--- | | No display on "HEATER LEVEL" when power is on. | - AC power cord is disconnected. - Fuses in the AC Power Inlet are blown. - Internal controlling board is malfunctioning. | - Firmly plug in the AC power cord. - Check and replace the fuse(s) with the correct rating. | | Pipette shape is different from usual, despite same settings. | - Heating element is deteriorated or contaminated. - Room temperature, humidity, or airflow (from AC) affecting the heating function. | - Increase the heater value to compensate. - Polish the mounting plates with sandpaper. - Move the instrument away from drafts. | | Pipette is distorted or off-centered. | - Glass capillary is not centered in the heating coil. - Heating coil coils are touching each other. | - Carefully re-center the capillary. - Use a wrench to separate the coils or replace the heater. | | Power blows fuse as soon as the device is turned on. | - A non-standard heating element is installed. - Heater values are set excessively high. | - Use only standard Narishige PC-10H elements. - Reduce heater value settings. |

You will also need to order consumable glass capillaries. The compatible glass types include:

: Set the heater block according to the glass capillary diameter.

Understanding the physical layout is key to navigating the manual 1.2.1.

: If the slider falls prematurely in two-stage mode, check the First Pull Terminating Position Adjusting Slider and ensure the solenoid coil is functioning.

For users seeking the "new" experience, the PC-100 represents the modern iteration of the instrument. Here's a quick comparison of their key differences:

: Ensure you're working with the most current version of the Narishige PC-10 manual to benefit from the latest information and recommendations.

A heavier weight (using 4x weights instead of 2x) results in a shorter, wider pull.

The original PC-10 uses mains voltage inside the case. A modernized manual should include warnings about capacitor discharge and heater element replacement frequency.

| Problem | Probable Cause(s) | Remedy(ies) | | :--- | :--- | :--- | | No display on "HEATER LEVEL" when power is on. | - AC power cord is disconnected. - Fuses in the AC Power Inlet are blown. - Internal controlling board is malfunctioning. | - Firmly plug in the AC power cord. - Check and replace the fuse(s) with the correct rating. | | Pipette shape is different from usual, despite same settings. | - Heating element is deteriorated or contaminated. - Room temperature, humidity, or airflow (from AC) affecting the heating function. | - Increase the heater value to compensate. - Polish the mounting plates with sandpaper. - Move the instrument away from drafts. | | Pipette is distorted or off-centered. | - Glass capillary is not centered in the heating coil. - Heating coil coils are touching each other. | - Carefully re-center the capillary. - Use a wrench to separate the coils or replace the heater. | | Power blows fuse as soon as the device is turned on. | - A non-standard heating element is installed. - Heater values are set excessively high. | - Use only standard Narishige PC-10H elements. - Reduce heater value settings. |

You will also need to order consumable glass capillaries. The compatible glass types include: